Exactly How to Install a Tub
Exactly How to Install a Tub
Blog Article
Just how do you really feel on the subject of A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open a wall to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have certified yourself for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new bathtub in your shower room if you have actually currently gotten a new tub and don't need to alter the setup of your previous water pipes.
Your devices and also product list need to comprise the following:
Planning for the Installment
To start with, the sustaining frame provided with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is often the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the level reviews level.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leaks and tighten them if necessary. Load the bath tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in place between the tap and also the sink. Secure the faucet in position with the supplier given backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in use. The sealer can split fairly early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Do you like reading about Installing A Bathtub? Place a remark directly below. We will be delighted to know your reactions about this article. Hoping to see you back again soon. Remember to take a moment to promote this page if you enjoyed it. Thank-you for your time spent reading it.
Call
Report this page